{"title":"Everlast Plasma Cutters","description":"\u003cp\u003eEverlast plasma cutters, including CNC-ready models.\u003c\/p\u003e","products":[{"product_id":"everlast-powerplasma-25i-xtr","title":"Everlast PowerPlasma 25i XTR","description":"\u003cp\u003eFor those looking for the ultimate 120V only plasma cutter with the best cutting performance and portability in the industry, the Everlast PowerPlasma 25i XTR delivers. With a maximum of 25 Amps output, the unit will sever up to 3\/8\", but also will deliver beautiful cuts right up to 1\/4\" thick with decent cut speed and low amounts of dross.  With a modern, blow-back style torch the unit avoids the pitfalls of old cheaper High Frequency designs, which include electronic interference and constant maintenance of the High Frequency points.  The unit has a simple front, single knob panel which outlines the expected output capacity on 15A, 20A, and 30A breakers. This acts as a guide to prevent accidental tripping of the breakers, if a 30A breaker isn't available.  This unit is perfect for operating on 4000 Watt Clean Power (5% or less THD) rated 120V generators. \u003c\/p\u003e\n\u003cp\u003eAs far as compressors go, this unit will operate on almost any 20 gallon compressor with moderate cutting.  For heavy cutting, consider a 30 gallon compressor.\u003c\/p\u003e\u003ch3\u003eFeatures \u0026amp; Benefits\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eOperates on 120V\u003c\/li\u003e\n\u003cli\u003e25A output \u003c\/li\u003e\n\u003cli\u003eCuts 1\/4\" cleanly\u003c\/li\u003e\n\u003cli\u003eSever up to 3\/8\"\u003c\/li\u003e\n\u003cli\u003eCompact IGBT inverter\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eStandard Equipment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eInnotec IPT-25 Plasma Torch with 12.5 ft cable\u003c\/li\u003e\n\u003cli\u003eGround Clamp with 5 ft cable and 25 Dinse Connector\u003c\/li\u003e\n\u003cli\u003eAir Filter\/Water Trap Regulator\u003c\/li\u003e\n\u003cli\u003eStarter Consumable Kit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eRecommended Areas of Use\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eMuffler Shops\u003c\/li\u003e\n\u003cli\u003eFarm and Ranch\u003c\/li\u003e\n\u003cli\u003eLight Fabrication\u003c\/li\u003e\n\u003cli\u003eHVAC\u003c\/li\u003e\n\u003cli\u003eAuto Body Restoration\u003c\/li\u003e\n\u003cli\u003eHobby\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eRecommended Metals\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSteel\u003c\/li\u003e\n\u003cli\u003eStainless\u003c\/li\u003e\n\u003cli\u003eAluminum Sheet\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eType\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eIGBT\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eVoltage\/phase\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e120V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOutput Amp\/Volt Range\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e10-25A, 84-90V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOCV\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e400V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMax Inrush ( I1MAX ) Amps\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e30A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMaximum Rated (I1EFF ) Input Amps\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e18A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eDuty Cycle At Rated Amps\/Volts\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e35% @ 25A\/90V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eArc Start Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eBlow Back (Piston type)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePilotArc\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eTorch Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eInnotec iPT 25\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eCNC Interface Port\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eNo\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eAdjustable Post Flow Timer\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eNo\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eGouging\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eNot Recommended\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRecommended Cutting Air Pressure\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e55 to 65 PSI\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRecommended Compressor Capacity\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e3.5 CFH @ 90 PSI with a 20 Gallon capacity\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOK-to-Cut Indicator\/Low Air pressure safety\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eWarranty\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e5 year\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eShipping Weight\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e21 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePart Number\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003ePP-25IXTR\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e","brand":"Everlast","offers":[{"title":"Default Title","offer_id":50925442236578,"sku":"PP-25IXTR","price":459.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0616\/9985\/0402\/files\/d181cdecb229d86ef937800b6437e2a3.png?v=1795135303"},{"product_id":"everlast-powerplasma-52i","title":"Everlast PowerPlasma 52i","description":"\u003cp\u003eFor customers looking for a compact, but reliable plasma cutter, the PowerPlasma 52i offers the latest in IGBT inverter design technology.  The PowerPlasma 52i is the successor to the popular and long running PowerPlasma 50S series which brought affordability and performance to the plasma cutter market place and gave customers a real choice.  Nothing has changed in that respect about the new PowerPlasma 52i.   The new PowerPlasma 52i has been completely redesigned though, offering full digital design, inside and out.  This has reduced circuit complexity, and improved reliability.    But it has also brought some new features which improve upon the solid platform of the PowerPlasma Series.   The new addition of the air-pressure guide system, offers digital display of actual air-pressure along with a LED system that guides the operator to the best choice of air pressure for the mode being used.   This new setup also features a digital control over Post-Flow and gives the user the ability to see and set the actual post flow time with a digital readout. It can be adjusted for different duty and job requirements. The Post-Flow can be easily increased to preserve consumable life for those long, time consuming cuts.  Or if you are doing rapid, short, or intermittent cuts, the Post-Flow time can be adjusted lower by just a quick twist of the dial.  The large digital displays are super bright, with improved visibility in bright conditions, making them easy to read at a distance.  Adding to the already long list of improvements, the PowerPlasma 52i, now has a gouge feature and a separate mode for CNC use.  The blow-back torch design features two pilot arc modes, one with continuous re-light for cutting expanded metal and for conditions where continuity is not ideal, and the other which features a tip saver function that limits pilot arc on time to preserve consumable life.\u003c\/p\u003e\u003ch3\u003eFeatures \u0026amp; Benefits\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDual Voltage 120\/240V for maximum portability\u003c\/li\u003e\n\u003cli\u003eAdjustable Post-Flow timer extends consumable and torch life\u003c\/li\u003e\n\u003cli\u003eLarge, Super bright digital displays for Amps, Air Pressure, and Post Flow\u003c\/li\u003e\n\u003cli\u003eDigital Air Pressure Setting Guide adapts programming for different cutting modes\u003c\/li\u003e\n\u003cli\u003eSeparate Gouge and CNC modes.\u003c\/li\u003e\n\u003cli\u003eEuro style \"Central\" quick connect torch adapter\u003c\/li\u003e\n\u003cli\u003eImproved Consumable life\u003c\/li\u003e\n\u003cli\u003eFeatures the Italian designed \"back striking\" iPT 60 torch with improved cutting capacity and improved consumable life\u003c\/li\u003e\n\u003cli\u003eInexpensive consumables can usually be bought locally\u003c\/li\u003e\n\u003cli\u003e60% duty cycle is fit for commercial use\u003c\/li\u003e\n\u003cli\u003eClean cuts and less bevel with the iPT 60 torch and new digitally controlled cutting arc.\u003c\/li\u003e\n\u003cli\u003eSelf-Diagnosing mode (Error Code)\u003c\/li\u003e\n\u003cli\u003eConsumables in Place Indicator.\u003c\/li\u003e\n\u003cli\u003ePilot arc tip saver feature limits pilot arc activity to 3 seconds. Continuous Pilot arc mode is standard as well.\u003c\/li\u003e\n\u003cli\u003eCan be used with 8500 watt clean power generators (less than 5% total harmonic distortion)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eStandard Equipment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eIPT-60 Handheld Torch with 14 ft. cable and Euro style Central connector\u003c\/li\u003e\n\u003cli\u003eGround Clamp with 10 ft. cable and 25 Dinse connector\u003c\/li\u003e\n\u003cli\u003eAW2000-02 Air Filter \/ Water Trap (gauge is not included)\u003c\/li\u003e\n\u003cli\u003eAir Hose\u003c\/li\u003e\n\u003cli\u003eWEiPU SP21 CNC Connector 12 Pin\u003c\/li\u003e\n\u003cli\u003eStarter Consumable Kit: 5x IPT-60 Electrodes and 5x IPT-60 1.1mm Nozzles\/Tips\u003c\/li\u003e\n\u003cli\u003ePigTail Adapter 120V\/240V\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eOptional Equipment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eProtective Cover\u003c\/li\u003e\n\u003cli\u003ePowerCart 250\u003c\/li\u003e\n\u003cli\u003eIPT-60 Plasma Torch 24 ft\u003c\/li\u003e\n\u003cli\u003ePTM-60 Plasma (CNC) Machine Torch\u003c\/li\u003e\n\u003cli\u003eIPT-60 Plasma Consumables Kits\u003c\/li\u003e\n\u003cli\u003eNOVA Welding and Fabrication Table\u003c\/li\u003e\n\u003cli\u003eNOVA Clamp and Tool Kit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eRecommended Areas of Use\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHome\/Hobby\u003c\/li\u003e\n\u003cli\u003eMetal Art\u003c\/li\u003e\n\u003cli\u003eFarm\/Ranch\u003c\/li\u003e\n\u003cli\u003eContstruction sites\u003c\/li\u003e\n\u003cli\u003ePortable Repair\u003c\/li\u003e\n\u003cli\u003eFabrication\u003c\/li\u003e\n\u003cli\u003eSmall CNC tables with 1\/4\" or less capacity is needed continuously\u003c\/li\u003e\n\u003cli\u003eAnywhere Oxy Fuel cutting is impractical, slow, expensive, or otherwise restricted or undesirable.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eRecommended Metals\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSteel\u003c\/li\u003e\n\u003cli\u003eStainless\u003c\/li\u003e\n\u003cli\u003eAluminum\u003c\/li\u003e\n\u003cli\u003eTitanium\u003c\/li\u003e\n\u003cli\u003eVirtually all types of metal\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eType\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eIGBT\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eVoltage\/phase\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eDual Voltage 120\/240 1 Phase\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOutput Amp\/Volt Range\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e120V: 20A\/88V-25A\/90V\u003cbr\u003e240V: 20A\/88V-50A\/100V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOCV\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e200V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMax Inrush ( I1MAX ) Amps\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e120V: 32.1A\u003cbr\u003e240V: 35.8A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMaximum Rated (I1EFF ) Input Amps\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e120V: 24.9A\u003cbr\u003e240V: 27.9A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eDuty Cycle At Rated Amps\/Volts\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e120V:  60% @ 25A\/90V\u003cbr\u003e240V: 60% @ 50A\/100V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eArc Start Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eBlow Back (Piston type)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePilotArc\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eTorch Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eItalian designed iPT 60\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eCNC Interface Port\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eAdjustable Post Flow Timer\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eGouging\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eLight or occasional\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRecommended Cutting Air Pressure\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e72-75 psi\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRecommended Compressor Capacity\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e5.0 cfm or better with 25 gallon tank\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOK-to-Cut Indicator\/Low Air pressure safety\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eWarranty\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e5 year\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eShipping Weight\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e40 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePart Number\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003ePP-52I\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e","brand":"Everlast","offers":[{"title":"Default Title","offer_id":50925442400418,"sku":"PP-52I","price":799.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0616\/9985\/0402\/files\/3707e557d4758f0e2c4af5b2204ea6d9.png?v=1795135303"},{"product_id":"everlast-powerplasma-62i","title":"Everlast PowerPlasma 62i","description":"\u003cp\u003eIf you are wanting more power, unquestionable cut quality, and reliabilty in a plasma cutter, but you just can't justify spending your green for something that is gray, the PowerPlasma 62i is the answer.  As the all new replacement for the ever popular PowerPlasma 60S, the PowerPlasma 62i has been built around a reliable, tested all digital inverter platform.  This allows the unit to do more with less circuitry and points of failure than ever before.  This plasma cutter though has kept all of the old features and added many new ones, so nothing was sacrificed in the way of features.  The display has been upgraded to offer large, easy to read numbers even in bright light.  The new addition of digital readouts for both the Post-Flow time and the Air-Pressure has added to the plasma cutter's operator oriented design.  Along with a digital display for the air pressure, the unit features an color coded LED guide system that helps you to properly set the air pressure for each cut mode without having to refer to a chart or manual.  A new gouge feature has been added for cutting out metal defects and old welds.  Also, a separate function has been added for CNC operation.  \u003c\/p\u003e\u003ch3\u003eFeatures \u0026amp; Benefits\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eEasy starting with Blow Back Pilot arc allows easy cutting of rusty and painted metals\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e\u003cem\u003eNEW! \u003c\/em\u003e\u003c\/strong\u003eDigitally controlled design that closely manages cutting arc\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e\u003cem\u003eNEW! \u003c\/em\u003e\u003c\/strong\u003eSuper bright displays, readable in bright light conditions\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e\u003cem\u003eNEW! \u003c\/em\u003e\u003c\/strong\u003eGouge function\u003c\/li\u003e\n\u003cli\u003eCuts virtually any type of metal with ease\u003c\/li\u003e\n\u003cli\u003eSimple to use torches with inexpensive service parts and consumables\u003c\/li\u003e\n\u003cli\u003eCommercial class, 60% Duty cycle at 60 amps\u003c\/li\u003e\n\u003cli\u003eClean, smooth cuts with the genuine iPT 60 Torch\u003c\/li\u003e\n\u003cli\u003eBlowback start starts are fast and reliable\u003c\/li\u003e\n\u003cli\u003ePilot arc improves performance and cutting on dirty, painted, or rusted metals \u003c\/li\u003e\n\u003cli\u003e3 Second pilot arc tip saver feature shuts down pilot arc after 3 seconds of continuous operation if no cutting is present to prevent premature consumable wear\u003c\/li\u003e\n\u003cli\u003eDigital Air Pressure Display, and LED Air Pressure guide system adapts to different cut modes for best air pressure setting without consulting a manual or chart\u003c\/li\u003e\n\u003cli\u003eSelf-diagnosing \u003c\/li\u003e\n\u003cli\u003eAdjustable postflow timer with digital display for maximum consumable life and ease of use.\u003c\/li\u003e\n\u003cli\u003eThe name brand IGBT's are digitally controlled which increases cut quality and consumable life.\u003c\/li\u003e\n\u003cli\u003eCNC socket and new, separate CNC cut mode for CNC use on plasma tables (machine torch optional)\u003c\/li\u003e\n\u003cli\u003eSuitable for use with 11,000 W \"clean power\" generators.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eStandard Equipment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eIPT-60 Handheld Torch with 14 ft. cable and Euro style Central connector\u003c\/li\u003e\n\u003cli\u003eGround Clamp with 10 ft. cable and 25 Dinse connector\u003c\/li\u003e\n\u003cli\u003eAW2000-02 Air Filter \/ Water Trap (gauge is not included)\u003c\/li\u003e\n\u003cli\u003eAir Hose\u003c\/li\u003e\n\u003cli\u003eWEiPU SP21 CNC Connector 12 Pin\u003c\/li\u003e\n\u003cli\u003eStarter Consumable Kit: 5x IPT-60 Electrodes and 5x IPT-60 1.1mm Nozzles\/Tips\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eOptional Equipment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eProtective Cover\u003c\/li\u003e\n\u003cli\u003eIPT-60 Plasma Torch 24 ft\u003c\/li\u003e\n\u003cli\u003ePTM-60 Plasma CNC\/Machine Torch\u003c\/li\u003e\n\u003cli\u003eIPT-60 Plasma Consumables Kits\u003c\/li\u003e\n\u003cli\u003eNOVA Welding and Fabrication Table\u003c\/li\u003e\n\u003cli\u003eNOVA Clamp and Tool Kit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eRecommended Areas of Use\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHome shop\u003c\/li\u003e\n\u003cli\u003eAutomotive\/muffler shops\u003c\/li\u003e\n\u003cli\u003eMotosports\u003c\/li\u003e\n\u003cli\u003eFarm\/Ranch\u003c\/li\u003e\n\u003cli\u003eCommercial fabrication\u003c\/li\u003e\n\u003cli\u003eFactory maintenance\u003c\/li\u003e\n\u003cli\u003eShipyards\u003c\/li\u003e\n\u003cli\u003ePipelines\u003c\/li\u003e\n\u003cli\u003eHVAC\u003c\/li\u003e\n\u003cli\u003eCNC\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eRecommended Metals\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSteel\u003c\/li\u003e\n\u003cli\u003eStainless\u003c\/li\u003e\n\u003cli\u003eAluminum\u003c\/li\u003e\n\u003cli\u003eCopper\u003c\/li\u003e\n\u003cli\u003eTitanium\u003c\/li\u003e\n\u003cli\u003eNickel\/Nickel alloys\u003c\/li\u003e\n\u003cli\u003eVirtually any metal including cast iron\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eType\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eIGBT\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eVoltage\/phase\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e220\/240 V 1 Phase\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOutput Amp\/Volt Range\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e20-60A; 88-104V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOCV\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e240V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMax Inrush ( I1MAX ) Amps\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e41A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMaximum Rated (I1EFF ) Input Amps\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e32.4A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eDuty Cycle At Rated Amps\/Volts\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e60% @ 60A\/104V\u003cbr\u003e100% @ 50A\/100V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eArc Start Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eBlow Back (Piston type)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePilotArc\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eTorch Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eItalian designed iPT 60\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eCNC Interface Port\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eAdjustable Post Flow Timer\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eGouging\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eLight to Medium\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRecommended Cutting Air Pressure\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e75 psi\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRecommended Compressor Capacity\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e6CFM @ 90 psi\/ 30 gallon tank\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOK-to-Cut Indicator\/Low Air pressure safety\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eWarranty\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e5 year\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eShipping Weight\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e74 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePart Number\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003ePP-62I\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e","brand":"Everlast","offers":[{"title":"Default Title","offer_id":50925442433186,"sku":"PP-62I","price":999.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0616\/9985\/0402\/files\/38af9757cfa77eb3d9003138e2539c96.png?v=1795135306"},{"product_id":"everlast-powerplasma-62i-with-cnc-package","title":"Everlast PowerPlasma 62i with CNC Package","description":"\u003cp\u003eFinally, it is here.  The proven PowerPlasma 62i is now available in a CNC only package.  This unit comes with all the basics to get started with your Plasma table, including CNC port, and CNC torch.  It has has the convenience, portability and performance that will meet the needs of everyone from the weekend enthusiast to the welding and fabrication shop operating a small plasma table.  The PowerPlasma 62i is built on an inverter platform, making use of IGBT technology to reduce weight, and improve reliability and performance. The unit has plenty of cut capacity with a recommended 3\/8\" regular cuts, maximum clean cut capability is up to 3\/4\" (at reduced speeds).  Pierce up to 5\/16\" for production cutting. The new PTM-60 CNC torch is part of the standard package and features a proven long life Italian design with blow back start, pilot arc and a variety of consumable choices.  The PowerPlasma 62i features a 3 second tip saver to reduce premature consumable wear by limiting pilot arc on time, if no cutting is taking place.\u003c\/p\u003e\u003ch3\u003eFeatures \u0026amp; Benefits\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eComes with CNC torch (Hand torch not included)\u003c\/li\u003e\n\u003cli\u003eEasy starting with Blow Back Pilot arc allows easy cutting of rusty and painted metals\u003c\/li\u003e\n\u003cli\u003eCuts virtually any type of metal with ease\u003c\/li\u003e\n\u003cli\u003eSimple to use torches with inexpensive service parts and consumables\u003c\/li\u003e\n\u003cli\u003eCommercial class, 60% Duty cycle at 60 amps for CNC use\u003c\/li\u003e\n\u003cli\u003eClean, smooth cuts with the genuine iPTM 60 CNC torch\u003c\/li\u003e\n\u003cli\u003eBlowback start starts arc without the need of High Frequency which can interfere with surrounding electronics\u003c\/li\u003e\n\u003cli\u003ePilot arc improves performance and cutting on dirty, painted, or rusted metals \u003c\/li\u003e\n\u003cli\u003e3 Second pilot arc tip saver feature shuts down pilot arc after 3 seconds of contiuous operation if no cutting is present to prevent premature consumable wear\u003c\/li\u003e\n\u003cli\u003eFront air pressure gauge allows quick verification of air pressure\u003c\/li\u003e\n\u003cli\u003eOver Current and Duty Cycle protection indicates fault with a dedicated warning\/diagnostic light, and shuts down output until condition is resolved\u003c\/li\u003e\n\u003cli\u003eAdjustable postflow timer for maximum consumable life\u003c\/li\u003e\n\u003cli\u003eIGBT components improve reliability and performance while reducing overall weight\u003c\/li\u003e\n\u003cli\u003eCNC socket for CNC use on plasma tables with included machine torch\u003c\/li\u003e\n\u003cli\u003eSuitable for use with 11,000 W \"clean power\" generators.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eStandard Equipment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePTM-60 CNC\/Machine Torch with 24 ft. cable and Euro quick-connect central connector\u003c\/li\u003e\n\u003cli\u003eGround Clamp with 10 ft. cable and 25 Dinse connector\u003c\/li\u003e\n\u003cli\u003eAW2000-02 Air Pressure Regulator\/Water Trap (separate air dryer is required to reduce consumable wear and prevent torch damage)\u003c\/li\u003e\n\u003cli\u003eStarter Consumable Kit: 5x IPT-60 Electrodes and 5x IPT-60 1.1mm Nozzles\/Tips\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eOptional Equipment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eProtective Cover\u003c\/li\u003e\n\u003cli\u003eIPT-60 Hand Held Plasma Torch 14 ft\u003c\/li\u003e\n\u003cli\u003eIPT-60 Hand Held Plasma Torch 24 ft\u003c\/li\u003e\n\u003cli\u003eIPT-60 Plasma Consumables Kits\u003c\/li\u003e\n\u003cli\u003eNOVA Welding and Fabrication Table\u003c\/li\u003e\n\u003cli\u003eNOVA Clamp and Tool Kit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eRecommended Areas of Use\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHome shop\u003c\/li\u003e\n\u003cli\u003eAutomotive\/muffler shops\u003c\/li\u003e\n\u003cli\u003eMotosports\u003c\/li\u003e\n\u003cli\u003eCommercial fabrication\u003c\/li\u003e\n\u003cli\u003eFactory maintenance\u003c\/li\u003e\n\u003cli\u003eShipyards\u003c\/li\u003e\n\u003cli\u003ePipelines\u003c\/li\u003e\n\u003cli\u003eHVAC\u003c\/li\u003e\n\u003cli\u003eCNC\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eRecommended Metals\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSteel\u003c\/li\u003e\n\u003cli\u003eStainless\u003c\/li\u003e\n\u003cli\u003eAluminum\u003c\/li\u003e\n\u003cli\u003eCopper\u003c\/li\u003e\n\u003cli\u003eTitanium\u003c\/li\u003e\n\u003cli\u003eNickel\/Nickel alloys\u003c\/li\u003e\n\u003cli\u003eVirtually any metal including cast iron\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eType\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eIGBT\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eVoltage\/phase\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e220\/240 V 1 Phase\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOutput Amp\/Volt Range\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e20-60A; 88-104V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOCV\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e240V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMax Inrush ( I1MAX ) Amps\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e41A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMaximum Rated (I1EFF ) Input Amps\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e32.4A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eDuty Cycle At Rated Amps\/Volts\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e60% @ 60A\/104V\u003cbr\u003e100% @ 50A\/100V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eArc Start Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eBlow Back (Piston type)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePilotArc\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eTorch Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eItalian designed iPT 60 CNC machine torch\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eCNC Interface Port\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eAdjustable Post Flow Timer\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eGouging\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eLight to Medium\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRecommended Cutting Air Pressure\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e75 psi\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRecommended Compressor Capacity\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e6CFM @ 90 psi\/ 30 gallon tank\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOK-to-Cut Indicator\/Low Air pressure safety\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eWarranty\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e5 year\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eShipping Weight\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e74 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePart Number\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003ePP-62I-CNC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e","brand":"Everlast","offers":[{"title":"Default Title","offer_id":50925442498722,"sku":"PP-62I-CNC","price":1250.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0616\/9985\/0402\/files\/64fb13060a08a89bdb53373c59c811f9.png?v=1795135307"},{"product_id":"everlast-powerplasma-82i","title":"Everlast PowerPlasma 82i","description":"\u003cp\u003eThe PowerPlasma 82i is really a plasma cutter in a class by itself.  When you consider the performance capability of the machine, design features and the price of the unit together, there really is nothing to compare it to.  Sure there are a couple of 80-90 Amp plasma cutters on the market, but hey, if you are on a budget, they aren't even close to what we offer in a machine this size when all things are considered overall.  Here's a few features that the PowerPlasma 82i has that that should get your attention:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eDigital Controlled Circuitry. This means reduced components and increased reliability\u003c\/li\u003e\n\u003cli\u003eA Digital Air Pressure Gauge.  You can precisely monitor air pressure fluctuations.\u003c\/li\u003e\n\u003cli\u003eDigital Air Pressure Setting Guide.  Color Coded LED's eliminate guess work for best air pressure setting.\u003c\/li\u003e\n\u003cli\u003eSuper Bright LED display.  Read your settings a greater distance and in brighter lighting than any other brand.\u003c\/li\u003e\n\u003cli\u003eAdjustable Post-Flow Control.  This allows you to be in charge of how long the air flows, reducing annoyingly and unecessarily long post flow time, reducing air consumption and noise levels from contantly running compressors.\u003c\/li\u003e\n\u003cli\u003eBuilt in CNC capability.  (See our CNC package for the machine torch option)\u003c\/li\u003e\n\u003cli\u003eGouge mode for moderate gouging needs.\u003c\/li\u003e\n\u003cli\u003eA Pilot Arc Tip saver function and a Auto-relight function allows you to choose the best mode of operation for to choose whether to maximize consumable life, or maximize cutting capability and speed on rusty\/painted or expanded metal.\u003c\/li\u003e\n\u003cli\u003e60% Duty Cycle takes the unit into a very exclusive club.   This is the highest rated duty cycle of any plasma cutter on the market on 1 phase 240V input.  The competitors offer only 50% and 40% duty cycles on 1 phase 240V.\u003c\/li\u003e\n\u003cli\u003e5 Year Warranty parts and labor warranty on the machine.  The best the competitors can do is 3 years.  \u003c\/li\u003e\n\u003cli\u003eA Price that beats anyone.  You'll be hard pressed to find a 40 amp plasma cutter at this price from the other guys.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFeatures \u0026amp; Benefits\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eEasy starting with Blow Back Pilot arc allows easy cutting of rusty and painted metals\u003c\/li\u003e\n\u003cli\u003eCuts virtually any type of metal with ease\u003c\/li\u003e\n\u003cli\u003eSimple to use torches with inexpensive service parts and consumables\u003c\/li\u003e\n\u003cli\u003eCommercial\/Industrial class, 60% Duty cycle at 80 amps\u003c\/li\u003e\n\u003cli\u003eClean, smooth cuts and improved consumable life with the new Italian designed iPT 80 torch\u003c\/li\u003e\n\u003cli\u003eBlowback start starts arc without the need of High Frequency which can interfere with surrounding electronics\u003c\/li\u003e\n\u003cli\u003ePilot arc improves performance and cutting on dirty, painted, or rusted metals \u003c\/li\u003e\n\u003cli\u003e3 Second pilot arc tip saver feature shuts down pilot arc after 3 seconds of contiuous operation if no cutting is present to prevent premature consumable wear\u003c\/li\u003e\n\u003cli\u003eAdjustable post flow control up to 50 seconds to improve consumable and torch life\u003c\/li\u003e\n\u003cli\u003eDigital air pressure gauge air pressure\u003c\/li\u003e\n\u003cli\u003eOver Current and Duty Cycle protection indicates fault with a dedicated warning\/diagnostic light, and shuts down output until condition is resolved\u003c\/li\u003e\n\u003cli\u003eDigital Air Pressure guide makes air pressure adjustment a no-brainer.\u003c\/li\u003e\n\u003cli\u003eCNC socket for CNC use on plasma tables (machine torch optional)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eStandard Equipment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eIPT-80 Hand Held Torch with 14 ft. cable and Euro quick-connect central connector\u003c\/li\u003e\n\u003cli\u003eGround Clamp with 25 Dinse connector\u003c\/li\u003e\n\u003cli\u003eAir Pressure Regulator\/Water Trap (separate air dryer is required to reduce consumable wear and prevent torch damage)\u003c\/li\u003e\n\u003cli\u003eConsumable starter kit: 5x IPT-80 Electrodes and 5x IPT-80 1.2mm Nozzles\/Tips\\\u003c\/li\u003e\n\u003cli\u003eWEiPU SP21 CNC Connector 12 Pin\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eOptional Equipment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eProtective Cover\u003c\/li\u003e\n\u003cli\u003eIPT-80 Hand Held Torch 24 ft.\u003c\/li\u003e\n\u003cli\u003eIPT-80 Plasma Consumables Kits\u003c\/li\u003e\n\u003cli\u003eIPT-80M Plasma Machine Torch (CNC)\u003c\/li\u003e\n\u003cli\u003eNOVA Welding and Fabrication Table\u003c\/li\u003e\n\u003cli\u003eNOVA Clamp and Tool Kit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eRecommended Areas of Use\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHome shop\u003c\/li\u003e\n\u003cli\u003eAutomotive\/muffler shops\u003c\/li\u003e\n\u003cli\u003eMotosports\u003c\/li\u003e\n\u003cli\u003eFarm\/Ranch\u003c\/li\u003e\n\u003cli\u003eCommercial fabrication\u003c\/li\u003e\n\u003cli\u003eFactory maintenance\u003c\/li\u003e\n\u003cli\u003eShipyards\u003c\/li\u003e\n\u003cli\u003ePipelines\u003c\/li\u003e\n\u003cli\u003eHVAC\u003c\/li\u003e\n\u003cli\u003eCNC\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eRecommended Metals\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSteel\u003c\/li\u003e\n\u003cli\u003eStainless\u003c\/li\u003e\n\u003cli\u003eAluminum\u003c\/li\u003e\n\u003cli\u003eCopper\u003c\/li\u003e\n\u003cli\u003eTitanium\u003c\/li\u003e\n\u003cli\u003eNickel\/Nickel alloys\u003c\/li\u003e\n\u003cli\u003eVirtually any metal including cast iron\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eType\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eIGBT\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eVoltage\/phase\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e220\/240 V 1 Phase\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOutput Amp\/Volt Range\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e20-80A\/88V-112V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOCV\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e240\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMax Inrush ( I1MAX ) Amps\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e@ 240V: 58A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMaximum Rated (I1EFF ) Input Amps\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e@240V: 45.2A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eDuty Cycle At Rated Amps\/Volts\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e60% @ 80A\/112V\u003cbr\u003e100% @ 63A\/105V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eArc Start Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eBlow Back (Piston type)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePilotArc\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eTorch Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eItalian designed iPT 80 torch\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eCNC Interface Port\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eAdjustable Post Flow Timer\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eGouging\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eLight to Medium\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRecommended Cutting Air Pressure\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e70-75psi\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRecommended Compressor Capacity\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e7CFM @ 90 psi\/60 gallon tank\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOK-to-Cut Indicator\/Low Air pressure safety\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eAmps\/Volts @ 60% Duty Cycle\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e80A\/ 112V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eWarranty\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e5 year\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eShipping Weight\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e77 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePart Number\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003ePP-82I\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e","brand":"Everlast","offers":[{"title":"Default Title","offer_id":50925442662562,"sku":"PP-82I","price":1269.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0616\/9985\/0402\/files\/b5fb1c0094a6d7a2382e89c771ef11ef.png?v=1795135308"},{"product_id":"everlast-powerplasma-82i-with-cnc-package","title":"Everlast PowerPlasma 82i with CNC Package","description":"\u003cp\u003eIf you are looking for a professional level plasma table machine that you aren't likely to quickly out grow, the Everlast PowerPlasma 82i with the CNC package is likely the one that you'd choose.  The portability, power, and performance, combine with the price to make the PowerPlasma 82i one of the best choices available in it's class when you consider power\/purchase cost ratios.  You get the best cut per amp per dollar paid for the PowerPlasma 82i CNC over any other 80 amp cutter in it's class. For routine daily use, the unit is recommended for cutting 5\/8\" thick plate metal.  And for maximum cut capability on CNC, this unit is capable of producing quality cuts of 1\" or greater (at reduced speeds).   Considering the purchase price, where else will you find a plasma cutter ready for plasma table use with a built in CNC socket and CNC torch?  Regarding portability, the unit's size is compact and can be easily stored or placed near the work area.  The new Italian designed PTM-80 CNC\/machine torch is rugged and features improved consumable life with the patented \"back striking\" design.  This blowback design torch comes with a variety of consumable choices, shielded and unshielded.  True it has a professional feel, capability and performance, but it also offers something for the hobbyist, with standard 240V operating input, which makes it right at home in any well equipped home shop plasma table or garage.\u003c\/p\u003e\u003ch3\u003eFeatures \u0026amp; Benefits\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eEasy starting with Blow Back Pilot arc allows easy cutting of rusty and painted metals\u003c\/li\u003e\n\u003cli\u003eCuts virtually any type of metal with ease\u003c\/li\u003e\n\u003cli\u003eSimple to use torches with inexpensive service parts and consumables\u003c\/li\u003e\n\u003cli\u003eCommercial\/Industrial class, 60% Duty cycle at 80 amps\u003c\/li\u003e\n\u003cli\u003eClean, smooth cuts and improved consumable life with the new Italian designed iPT 80 torch\u003c\/li\u003e\n\u003cli\u003eBlowback start starts arc without the need of High Frequency which can interfere with surrounding electronics\u003c\/li\u003e\n\u003cli\u003ePilot arc improves performance and cutting on dirty, painted, or rusted metals \u003c\/li\u003e\n\u003cli\u003e3 Second pilot arc tip saver feature shuts down pilot arc after 3 seconds of contiuous operation if no cutting is present to prevent premature consumable wear\u003c\/li\u003e\n\u003cli\u003eAdjustable post flow control up to 50 seconds to improve consumable and torch life\u003c\/li\u003e\n\u003cli\u003eFront air pressure gauge allows quick verification of air pressure\u003c\/li\u003e\n\u003cli\u003eOver Current and Duty Cycle protection indicates fault with a dedicated warning\/diagnostic light, and shuts down output until condition is resolved\u003c\/li\u003e\n\u003cli\u003eIGBT modules improve reliability and performance while reducing overall weight\u003c\/li\u003e\n\u003cli\u003eCNC socket and CNC torch for plasma table use.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eStandard Equipment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePTM-80 CNC\/Machine Torch with 24 ft. cable and Euro quick-connect central connector\u003c\/li\u003e\n\u003cli\u003eGround Clamp with 25 Dinse Connector\u003c\/li\u003e\n\u003cli\u003eAir Pressure Regulator\/Water Trap (gauge is not included \/ separate air dryer is required to reduce consumable wear and prevent torch damage)\u003c\/li\u003e\n\u003cli\u003eConsumable starter kit: 5x IPT-80 Electrodes and 5x IPT-80 1.2mm Nozzles\/Tips\u003c\/li\u003e\n\u003cli\u003eWEiPU SP21 CNC Connector 12 Pin\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eOptional Equipment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eProtective Cover\u003c\/li\u003e\n\u003cli\u003eIPT-80 Hand Held Plasma Torch 14 ft\u003c\/li\u003e\n\u003cli\u003eIPT-80 Hand Held Plasma Torch 24 ft\u003c\/li\u003e\n\u003cli\u003eIPT-80 Plasma Consumables Kits\u003c\/li\u003e\n\u003cli\u003eNOVA Welding and Fabrication Table\u003c\/li\u003e\n\u003cli\u003eNOVA Clamp and Tool Kit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eRecommended Areas of Use\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHome shop\u003c\/li\u003e\n\u003cli\u003eMotosports\u003c\/li\u003e\n\u003cli\u003eFarm\/Ranch\u003c\/li\u003e\n\u003cli\u003eCommercial fabrication\u003c\/li\u003e\n\u003cli\u003eFactory maintenance\u003c\/li\u003e\n\u003cli\u003eHVAC\u003c\/li\u003e\n\u003cli\u003eCNC\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eRecommended Metals\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSteel\u003c\/li\u003e\n\u003cli\u003eStainless\u003c\/li\u003e\n\u003cli\u003eAluminum\u003c\/li\u003e\n\u003cli\u003eCopper\u003c\/li\u003e\n\u003cli\u003eTitanium\u003c\/li\u003e\n\u003cli\u003eNickel\/Nickel alloys\u003c\/li\u003e\n\u003cli\u003eVirtually any metal including cast iron\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eType\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eIGBT\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eVoltage\/phase\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e220\/240 V 1 Phase\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOutput Amp\/Volt Range\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e20-80A\/88V-112V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOCV\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e240V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMax Inrush ( I1MAX ) Amps\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e@ 240V: 58A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMaximum Rated (I1EFF ) Input Amps\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e@240V: 45.2A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eDuty Cycle At Rated Amps\/Volts\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e60% @ 80A\/112V\u003cbr\u003e100% @ 63A\/105V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eArc Start Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eBlow Back (Piston type)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePilotArc\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eTorch Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eItalian designed iPT 80 machine torch\u003cbr\u003e(Hand torch not included)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eCNC Interface Port\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eAdjustable Post Flow Timer\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eGouging\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eLight to Medium\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRecommended Cutting Air Pressure\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e75psi\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRecommended Compressor Capacity\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e7CFM @ 90 psi\/60 gallon tank\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOK-to-Cut Indicator\/Low Air pressure safety\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eWarranty\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e5 year\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eShipping Weight\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e77 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePart Number\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003ePP-82I-CNC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e","brand":"Everlast","offers":[{"title":"Default Title","offer_id":50925442760866,"sku":"PP-82I-CNC","price":1469.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0616\/9985\/0402\/files\/82bedf9509137f61b6b65f20b95c43d3.png?v=1795135309"},{"product_id":"everlast-powerplasma-102i-1-3-phase-240v","title":"Everlast PowerPlasma 102i (1\/3 Phase 240V)","description":"\u003cp\u003eThe PowerPlasma 102i is designed for heavy duty plasma cutting service.  With up to 100 amps of cutting power, the original unit has proven its performance and reliability in industrial and fabrication settings since 2008.  The newest version has been redesigned for a more compact stature. The IGBT inverter design is reliably engineered to provide heavy duty service with a 60% duty cycle at maximum amps.  This is enough to sever metal up to 1 5\/8\" thick when needed.  For daily use, it works great for regularly cutting 1 1\/4\" thick plate metal, and when called upon, makes a clean cut up to 1 1\/2\".  The heavy duty Innotec IPT-100 blow back torch features a Euro, quick connect central adapter for easy connection.  Priced around the price of some 40-50 amp plasma cutters on the market, this Everlast IGBT inverter plasma cutter clearly doesn't go slack on performance.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eNOTE\u003c\/strong\u003e:  This unit is for 1 and 3 Phase 240V input.  For 480V 3 phase operation, please see that listing: PowerPlasma 102i (3 Phase 480V)\u003c\/p\u003e\u003ch3\u003eFeatures \u0026amp; Benefits\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eEasy starting with Blow Back Pilot arc allows easy cutting of rusty and painted metals\u003c\/li\u003e\n\u003cli\u003eCuts virtually any type of metal with ease\u003c\/li\u003e\n\u003cli\u003eSimple to use torches with inexpensive service parts and consumables\u003c\/li\u003e\n\u003cli\u003eCommercial class, 60% Duty cycle at 100 amps\u003c\/li\u003e\n\u003cli\u003eClean, smooth cuts with the genuine Innotec iPT100 torch.\u003c\/li\u003e\n\u003cli\u003ePilot arc improves performance and cutting on dirty, painted, or rusted metals \u003c\/li\u003e\n\u003cli\u003eFront air pressure gauge allows quick verification of air pressure\u003c\/li\u003e\n\u003cli\u003eOver Current and Duty Cycle protection indicates fault with a dedicated warning\/diagnostic light, and shuts down output until condition is resolved\u003c\/li\u003e\n\u003cli\u003eIGBT modules improve reliability and performance while reducing overall weight\u003c\/li\u003e\n\u003cli\u003eCNC socket for CNC use on plasma tables (machine torch optional)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eStandard Equipment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eIPT-100 Hand Held Torch 14 ft. cable and Euro quick-connect Central connector\u003c\/li\u003e\n\u003cli\u003eGround Clamp with 10 ft. cable and 25 Dinse connector\u003c\/li\u003e\n\u003cli\u003eAW3000-02 Air Filter \/ Water Trap (gauge is not included)\u003c\/li\u003e\n\u003cli\u003eConsumable starter kit: 5x IPT-100 Electrodes and 5x IPT-100 1.5mm Nozzles\/Tips\u003c\/li\u003e\n\u003cli\u003eWEiPU SP21 CNC Connector 12 Pin\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eOptional Equipment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eProtective Cover\u003c\/li\u003e\n\u003cli\u003eIPT-100 Hand Held Torch 25 ft.\u003c\/li\u003e\n\u003cli\u003eIPT-100 Plasma Consumables Kits\u003c\/li\u003e\n\u003cli\u003ePTM-100 CNC\/Machine Torch\u003c\/li\u003e\n\u003cli\u003eNOVA Welding and Fabrication Table\u003c\/li\u003e\n\u003cli\u003eNOVA Clamp and Tool Kit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eRecommended Areas of Use\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eIndustrial Fabrication\u003c\/li\u003e\n\u003cli\u003ePipelines\u003c\/li\u003e\n\u003cli\u003eShipyards\u003c\/li\u003e\n\u003cli\u003eMotorsports facilities\u003c\/li\u003e\n\u003cli\u003eRepair shops\u003c\/li\u003e\n\u003cli\u003eRail Road maintenance\u003c\/li\u003e\n\u003cli\u003eHVAC\u003c\/li\u003e\n\u003cli\u003eHeavy Equipment Repair\u003c\/li\u003e\n\u003cli\u003eFarm\/Ranch\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eRecommended Metals\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSteel\u003c\/li\u003e\n\u003cli\u003eStainless\u003c\/li\u003e\n\u003cli\u003eAluminum\u003c\/li\u003e\n\u003cli\u003eNickel\u003c\/li\u003e\n\u003cli\u003eTitanium\u003c\/li\u003e\n\u003cli\u003eCopper\u003c\/li\u003e\n\u003cli\u003eCast iron\u003c\/li\u003e\n\u003cli\u003eVirtually all metals\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eType\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eIGBT\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eVoltage\/phase\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e220\/240 V 1\/3 Phase\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOutput Amp\/Volt Range\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e20-100A\/88-120V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOCV\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e250V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMax Inrush ( I1MAX ) Amps\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e240V 1 phase:  78A\u003cbr\u003e240V 3 phase:  45.2A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMaximum Rated (I1EFF ) Input Amps\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e240V 1 phase: 61A\u003cbr\u003e240V 3 phase: 36A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eDuty Cycle At Rated Amps\/Volts\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e60% @ 100A\/120V\u003cbr\u003e100% @ 80A\/112V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eArc Start Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eBlow Back (Piston type)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePilotArc\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eTorch Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eGenuine Innotec iPT100\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eCNC Interface Port\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eAdjustable Post Flow Timer\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eGouging\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRecommended Cutting Air Pressure\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e65-72 psi\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRecommended Compressor Capacity\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eMinimum of 9 CFM @90 psi, 60-80 gallon tank\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOK-to-Cut Indicator\/Low Air pressure safety\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eWarranty\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e5 year\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eShipping Weight\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e72 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePart Number\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003ePP-102I-240\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e","brand":"Everlast","offers":[{"title":"Default Title","offer_id":50925442826402,"sku":"PP-102I-240","price":1799.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0616\/9985\/0402\/files\/2d2a1ab51d10c24118f4c6e29d5250d9.png?v=1795135310"},{"product_id":"everlast-powerplasma-102i-plasma-cutter-with-cnc-option-1-3-phase-240v","title":"Everlast PowerPlasma 102i Plasma Cutter with CNC Option (1\/3 Phase 240V)","description":"\u003cp\u003eThe PowerPlasma 102i is designed for heavy duty plasma cutting service.  With up to 100 amps of cutting power, the original unit has proven its performance and reliability in industrial and fabrication settings since 2008.  The newest version has been redesigned for a more compact stature. The IGBT inverter design is reliably engineered to provide heavy duty service with a 60% duty cycle at maximum amps.  This is enough to sever metal up to 1 5\/8\" thick when needed.  For daily use, it works great for regularly cutting 1 1\/4\" thick plate metal, and when called upon, makes a clean cut up to 1 1\/2\".  The heavy duty Innotec IPT-100 blow back torch features a Euro, quick connect central adapter for easy connection.  Priced around the price of some 40-50 amp plasma cutters on the market, this Everlast IGBT inverter plasma cutter clearly doesn't go slack on performance.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eNOTE\u003c\/strong\u003e:  This unit is for 1 and 3 Phase 240V input.  For 480V 3 phase operation, please see that listing: PowerPlasma 102i (3 Phase 480V)\u003c\/p\u003e\u003ch3\u003eFeatures \u0026amp; Benefits\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eEasy starting with Blow Back Pilot arc allows easy cutting of rusty and painted metals\u003c\/li\u003e\n\u003cli\u003eCuts virtually any type of metal with ease\u003c\/li\u003e\n\u003cli\u003eSimple to use torches with inexpensive service parts and consumables\u003c\/li\u003e\n\u003cli\u003eCommercial class, 60% Duty cycle at 100 amps\u003c\/li\u003e\n\u003cli\u003eClean, smooth cuts with the genuine Innotec iPT100 torch.\u003c\/li\u003e\n\u003cli\u003ePilot arc improves performance and cutting on dirty, painted, or rusted metals \u003c\/li\u003e\n\u003cli\u003eFront air pressure gauge allows quick verification of air pressure\u003c\/li\u003e\n\u003cli\u003eOver Current and Duty Cycle protection indicates fault with a dedicated warning\/diagnostic light, and shuts down output until condition is resolved\u003c\/li\u003e\n\u003cli\u003eIGBT modules improve reliability and performance while reducing overall weight\u003c\/li\u003e\n\u003cli\u003eCNC socket for CNC use on plasma tables (machine torch optional)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eStandard Equipment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eIPT-100 Hand Held Torch 14 ft. cable and Euro quick-connect Central connector\u003c\/li\u003e\n\u003cli\u003eGround Clamp with 10 ft. cable and 25 Dinse connector\u003c\/li\u003e\n\u003cli\u003eAW3000-02 Air Filter \/ Water Trap (gauge is not included)\u003c\/li\u003e\n\u003cli\u003eConsumable starter kit: 5x IPT-100 Electrodes and 5x IPT-100 1.5mm Nozzles\/Tips\u003c\/li\u003e\n\u003cli\u003eWEiPU SP21 CNC Connector 12 Pin\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eOptional Equipment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eProtective Cover\u003c\/li\u003e\n\u003cli\u003eIPT-100 Hand Held Torch 25 ft.\u003c\/li\u003e\n\u003cli\u003eIPT-100 Plasma Consumables Kits\u003c\/li\u003e\n\u003cli\u003ePTM-100 CNC\/Machine Torch\u003c\/li\u003e\n\u003cli\u003eNOVA Welding and Fabrication Table\u003c\/li\u003e\n\u003cli\u003eNOVA Clamp and Tool Kit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eRecommended Areas of Use\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eIndustrial Fabrication\u003c\/li\u003e\n\u003cli\u003ePipelines\u003c\/li\u003e\n\u003cli\u003eShipyards\u003c\/li\u003e\n\u003cli\u003eMotorsports facilities\u003c\/li\u003e\n\u003cli\u003eRepair shops\u003c\/li\u003e\n\u003cli\u003eRail Road maintenance\u003c\/li\u003e\n\u003cli\u003eHVAC\u003c\/li\u003e\n\u003cli\u003eHeavy Equipment Repair\u003c\/li\u003e\n\u003cli\u003eFarm\/Ranch\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eRecommended Metals\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSteel\u003c\/li\u003e\n\u003cli\u003eStainless\u003c\/li\u003e\n\u003cli\u003eAluminum\u003c\/li\u003e\n\u003cli\u003eNickel\u003c\/li\u003e\n\u003cli\u003eTitanium\u003c\/li\u003e\n\u003cli\u003eCopper\u003c\/li\u003e\n\u003cli\u003eCast iron\u003c\/li\u003e\n\u003cli\u003eVirtually all metals\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eWarranty\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e5 year\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eShipping Weight\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e72 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePart Number\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003ePP-102I-CNC-240\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003cp\u003e\u003cem\u003eThis listing is the PowerPlasma 102i Plasma Cutter with CNC Option (1\/3 Phase 240V) configuration (Everlast part number PP-102I-CNC-240).\u003c\/em\u003e\u003c\/p\u003e","brand":"Everlast","offers":[{"title":"Default Title","offer_id":50925442859170,"sku":"PP-102I-CNC-240","price":1999.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0616\/9985\/0402\/files\/2d2a1ab51d10c24118f4c6e29d5250d9_5ca17b7c-0cf3-4bea-910a-67d63d33e588.png?v=1795135310"},{"product_id":"everlast-powerplasma-102i-3-phase-480v","title":"Everlast PowerPlasma 102i (3 Phase 480V)","description":"\u003cp\u003eThe PowerPlasma 102i is designed for heavy duty plasma cutting service.  With up to 100 amps of cutting power, the original unit has proven its performance and reliability in industrial and fabrication settings since 2008.  The newest version has been redesigned for a more compact stature. The IGBT inverter design is reliably engineered to provide heavy duty service with a 60% duty cycle at maximum amps.  This is enough to sever metal up to 1 5\/8\" thick when needed.  For daily use, it works great for regularly cutting 1 1\/4\" thick plate metal, and when called upon, makes a clean cut up to 1 1\/2\".  The heavy duty Innotec IPT-100 blow back torch features a Euro, quick connect central adapter for easy connection.  Priced around the price of some 40-50 amp plasma cutters on the market, this Everlast IGBT inverter plasma cutter clearly doesn't go slack on performance.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eNOTE\u003c\/strong\u003e:  This unit is for \u003cu\u003e3 Phase 480V\u003c\/u\u003e operation only.\u003c\/p\u003e\u003ch3\u003eFeatures \u0026amp; Benefits\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eEasy starting with Blow Back Pilot arc allows easy cutting of rusty and painted metals\u003c\/li\u003e\n\u003cli\u003eCuts virtually any type of metal with ease\u003c\/li\u003e\n\u003cli\u003eSimple to use torches with inexpensive service parts and consumables\u003c\/li\u003e\n\u003cli\u003eCommercial class, 60% Duty cycle at 100 amps\u003c\/li\u003e\n\u003cli\u003eClean, smooth cuts with the genuine Innotec iPT100 torch.\u003c\/li\u003e\n\u003cli\u003ePilot arc improves performance and cutting on dirty, painted, or rusted metals \u003c\/li\u003e\n\u003cli\u003eFront air pressure gauge allows quick verification of air pressure\u003c\/li\u003e\n\u003cli\u003eOver Current and Duty Cycle protection indicates fault with a dedicated warning\/diagnostic light, and shuts down output until condition is resolved\u003c\/li\u003e\n\u003cli\u003eIGBT modules improve reliability and performance while reducing overall weight\u003c\/li\u003e\n\u003cli\u003eCNC socket for CNC use on plasma tables (machine torch optional)\u003c\/li\u003e\n\u003cli\u003e480V 3 Phase Input\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eStandard Equipment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eIPT-100 Hand Held Torch 14 ft. cable and Euro quick-connect Central connector\u003c\/li\u003e\n\u003cli\u003eGround Clamp with 10 ft. cable and 25 Dinse connector\u003c\/li\u003e\n\u003cli\u003eAW3000-02 Air Filter \/ Water Trap (gauge is not included)\u003c\/li\u003e\n\u003cli\u003eConsumable starter kit: 5x IPT-100 Electrodes and 5x IPT-100 1.5mm Nozzles\/Tips\u003c\/li\u003e\n\u003cli\u003eWEiPU SP21 CNC Connector 12 Pin\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eOptional Equipment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eWelder Cover\u003c\/li\u003e\n\u003cli\u003eIPT-100 Plasma Torch 25 ft.\u003c\/li\u003e\n\u003cli\u003eIPT-100 Plasma Consumable Kits\u003c\/li\u003e\n\u003cli\u003ePTM-100 CNC\/Machine Torch\u003c\/li\u003e\n\u003cli\u003eNOVA Welding and Fabrication Table\u003c\/li\u003e\n\u003cli\u003eNOVA Clamp and Tool Kit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eRecommended Areas of Use\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eIndustrial Fabrication\u003c\/li\u003e\n\u003cli\u003ePipelines\u003c\/li\u003e\n\u003cli\u003eShipyards\u003c\/li\u003e\n\u003cli\u003eMotorsports facilities\u003c\/li\u003e\n\u003cli\u003eRepair shops\u003c\/li\u003e\n\u003cli\u003eRail Road maintenance\u003c\/li\u003e\n\u003cli\u003eHVAC\u003c\/li\u003e\n\u003cli\u003eHeavy Equipment Repair\u003c\/li\u003e\n\u003cli\u003eFarm\/Ranch\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eRecommended Metals\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSteel\u003c\/li\u003e\n\u003cli\u003eStainless\u003c\/li\u003e\n\u003cli\u003eAluminum\u003c\/li\u003e\n\u003cli\u003eNickel\u003c\/li\u003e\n\u003cli\u003eTitanium\u003c\/li\u003e\n\u003cli\u003eCopper\u003c\/li\u003e\n\u003cli\u003eCast iron\u003c\/li\u003e\n\u003cli\u003eVirtually all metals\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eType\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eIGBT\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eVoltage\/phase\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e480 V 3 Phase (Available as Option)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOutput Amp\/Volt Range\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e20-100A\/88-120V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOCV\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e300V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMax Inrush ( I1MAX ) Amps\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e480V 3 Phase: 20.6A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMaximum Rated (I1EFF ) Input Amps\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e480V 3 Phase: 17A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eDuty Cycle At Rated Amps\/Volts\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e60% @ 100A\/120V\u003cbr\u003e100% @ 80A\/112V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eArc Start Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eBlow Back (Piston type)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePilotArc\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eTorch Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eGenuine Innotec iPT100\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eCNC Interface Port\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eAdjustable Post Flow Timer\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eGouging\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRecommended Cutting Air Pressure\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e65-72 psi\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRecommended Compressor Capacity\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eMinimum of 9 CFM @90 psi, 60-80 gallon tank\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOK-to-Cut Indicator\/Low Air pressure safety\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eWarranty\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e5 year\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eShipping Weight\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e84 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePart Number\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003ePP-102I-480\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e","brand":"Everlast","offers":[{"title":"Default Title","offer_id":50925442957474,"sku":"PP-102I-480","price":1999.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0616\/9985\/0402\/files\/b5712d9d35b89ea2332da9d0e6e345d0.png?v=1795135312"},{"product_id":"everlast-powerplasma-102i-cnc-pkg-3-phase-480v","title":"Everlast PowerPlasma 102i CNC Pkg (3 Phase 480V)","description":"\u003cp\u003eIf you are looking for a high capacity plasma cutter for a professional plasma table machine that keeps you on budget, the Everlast PowerPlasma 102i with the CNC package is definitely a strong competitor.  The portability, power, and performance, combine with the price to make the PowerPlasma 102i one of the best choices available in it's class when you consider cut capability to purchase cost ratios.  You get the best cut per amp per dollar paid for the PowerPlasma 102i CNC over any other 100 amp cutter in it's class. For routine daily use, the unit is recommended for cutting 3\/4\" thick plate metal.  And for maximum cut capability on CNC, this unit is capable of producing quality cuts of 1 1\/8\" or greater (at reduced speeds).   With a built in CNC socket and CNC torch this package is ready to be connected to your plasma table.  All you have to do is connect the plasma table control wires to the socket connector.  The unit's compact size lends itself to being stored or placed near the work area.  The new Italian designed iPT 100M machine\/CNC torch is rugged and features improved consumable life with the patented \"back striking\" design.  This blowback design torch offers a variety of consumable choices, shielded and unshielded.  The performance and cut capability at the price level the PowerPlasma 102i CNC package is simply unmatched in the industry. This unit is for 3 phase 480V operation. \u003c\/p\u003e\u003ch3\u003eFeatures \u0026amp; Benefits\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eEasy starting with Blow Back Pilot arc allows easy cutting of rusty and painted metals\u003c\/li\u003e\n\u003cli\u003eCuts virtually any type of metal with ease\u003c\/li\u003e\n\u003cli\u003eSimple to use torches with inexpensive service parts and consumables\u003c\/li\u003e\n\u003cli\u003eCommercial\/Industrial class, 60% Duty cycle at 100 amps\u003c\/li\u003e\n\u003cli\u003eClean, smooth cuts and improved consumable life with the new Italian designed iPT 100M torch\u003c\/li\u003e\n\u003cli\u003eBlowback start starts arc without the need of High Frequency which can interfere with surrounding electronics\u003c\/li\u003e\n\u003cli\u003ePilot arc improves performance and cutting on dirty, painted, or rusted metals \u003c\/li\u003e\n\u003cli\u003e3 Second pilot arc tip saver feature shuts down pilot arc after 3 seconds of contiuous operation if no cutting is present to prevent premature consumable wear\u003c\/li\u003e\n\u003cli\u003eAdjustable post flow control up to 50 seconds to improve consumable and torch life\u003c\/li\u003e\n\u003cli\u003eFront air pressure gauge allows quick verification of air pressure\u003c\/li\u003e\n\u003cli\u003eOver Current and Duty Cycle protection indicates fault with a dedicated warning\/diagnostic light, and shuts down output until condition is resolved\u003c\/li\u003e\n\u003cli\u003eIGBT modules improve reliability and performance while reducing overall weight\u003c\/li\u003e\n\u003cli\u003eCNC socket and CNC torch for plasma table use.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eStandard Equipment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e25ft. Italian designed and patented iPT 100M CNC torch with Euro quick-connect central adapter\u003c\/li\u003e\n\u003cli\u003eWork clamp with 10ft. cable and DINSE connector\u003c\/li\u003e\n\u003cli\u003eAir pressure regulator\/water trap (Separate air dryer is required to reduce consumable wear and prevent torch damage)\u003c\/li\u003e\n\u003cli\u003eConsumable starter kit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eOptional Equipment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eWelder Cover\u003c\/li\u003e\n\u003cli\u003eNOVA Welding and Fabrication Table\u003c\/li\u003e\n\u003cli\u003eNOVA Clamp and Tool Kit\u003c\/li\u003e\n\u003cli\u003eiPT-100 Hand-held Plasma Torch, 15 ft\u003c\/li\u003e\n\u003cli\u003eiPT-100 Hand-held Plasma Torch, 25 ft\u003c\/li\u003e\n\u003cli\u003eiPT-100 Plasma Consumables Kits\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eRecommended Areas of Use\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHome shop\u003c\/li\u003e\n\u003cli\u003eMotosports\u003c\/li\u003e\n\u003cli\u003eFarm\/Ranch\u003c\/li\u003e\n\u003cli\u003eCommercial fabrication\u003c\/li\u003e\n\u003cli\u003eFactory maintenance\u003c\/li\u003e\n\u003cli\u003eHVAC\u003c\/li\u003e\n\u003cli\u003eCNC\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eRecommended Metals\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSteel\u003c\/li\u003e\n\u003cli\u003eStainless\u003c\/li\u003e\n\u003cli\u003eAluminum\u003c\/li\u003e\n\u003cli\u003eCopper\u003c\/li\u003e\n\u003cli\u003eTitanium\u003c\/li\u003e\n\u003cli\u003eNickel\/Nickel alloys\u003c\/li\u003e\n\u003cli\u003eVirtually any metal including cast iron\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eType\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eIGBT\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eVoltage\/phase\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e480 V 3 Phase (Available as Option)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOutput Amp\/Volt Range\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e20-100A\/88V-120V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOCV\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e250V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eDuty Cycle At Rated Amps\/Volts\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e60% @ 100A\/120V\u003cbr\u003e100% @ 80A\/112V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eArc Start Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eBlow Back (Piston type)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePilotArc\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eTorch Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eItalian designed iPT 100M machine torch\u003cbr\u003e(Hand torch not included)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eCNC Interface Port\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eAdjustable Post Flow Timer\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRecommended Cutting Air Pressure\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e75psi\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRecommended Compressor Capacity\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e8CFM @ 90 psi\/60 gallon tank\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOK-to-Cut Indicator\/Low Air pressure safety\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eWarranty\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e5 year\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eShipping Weight\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e84 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePart Number\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003ePP-102I-CNC-480\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e","brand":"Everlast","offers":[{"title":"Default Title","offer_id":50925443055778,"sku":"PP-102I-CNC-480","price":2299.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0616\/9985\/0402\/files\/1027a962dc6f56a15bad9c0a2e64ce99.png?v=1795135312"},{"product_id":"everlast-powerplasma-160h-plasma-cutter-with-high-frequency-480v-3-phase","title":"Everlast PowerPlasma 160H Plasma Cutter with High Frequency (480V 3-Phase)","description":"\u003cp\u003eEverlast PowerPlasma 160H Plasma Cutter with High Frequency (480V 3-Phase).\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eShipping Weight\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e153 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePart Number\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003ePP160H-480\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e","brand":"Everlast","offers":[{"title":"Default Title","offer_id":50925443121314,"sku":"PP160H-480","price":3499.0,"currency_code":"USD","in_stock":true}]},{"product_id":"everlast-hatchet-60","title":"Everlast Hatchet 60","description":"\u003cp\u003eReady to chop up a bit of metal?  The \"Hatchet\" is a no-nonsense type of cutter designed just for hand cutting that stands ready to accurately tackle common every day chores in small shops and home garages. The small stature and light weight of the cutter indicates that this unit is designed to be a space saver.  Add to that fact the 120\/240V dual voltage operating capability of the machine, and you'll see that the unit is perfect for those needing to go portable for the race track, restaurants or even light HVAC work.  For those needing more power and portablity out on the jobsite, this unit will operate off any clean power (5% or less THD) generator capable of producing 10,000 Surge Watts of power.  \u003c\/p\u003e\n\u003cp\u003eWhether it's at the race track, home, work or out in the field on the farm, this unit will work day in and day out for you.  It's also covered by the 5 year parts and labor warranty that covers all Everlast IGBT products.\u003c\/p\u003e\n\u003cp\u003eThis unit is not intended for gouging. If you have gouging needs see one of our PowerPlasma models.  For a 60A unit with gouging capability see here:  https:\/\/www.everlastgenerators.com\/product\/plasma\/powerplasma-62i\u003c\/p\u003e\u003ch3\u003eFeatures \u0026amp; Benefits\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eEasy starting with Blow Back Pilot arc allows easy cutting of rusty and painted metals\u003c\/li\u003e\n\u003cli\u003eCuts virtually any type of Metal\u003c\/li\u003e\n\u003cli\u003eSimple to use torches with inexpensive service parts and consumables\u003c\/li\u003e\n\u003cli\u003eLight Commercial class, 35% Duty cycle at 60 amps\u003c\/li\u003e\n\u003cli\u003eClean, smooth cuts with the genuine iPT 60 Torch\u003c\/li\u003e\n\u003cli\u003eBlowback start starts are fast and reliable\u003c\/li\u003e\n\u003cli\u003ePilot arc improves performance and cutting on dirty, painted, or rusted metals \u003c\/li\u003e\n\u003cli\u003eAuto pilot arc restart and Auto post flow\u003c\/li\u003e\n\u003cli\u003eFront mounted pressure gauge\u003c\/li\u003e\n\u003cli\u003eSuitable for use with 10,000 W \"clean power\" (5% or less THD) generators\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eStandard Equipment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eIPT-60 Hand Held Torch 14 ft. with Euro quick-connect central connector\u003c\/li\u003e\n\u003cli\u003eGround Clamp with 25 Dinse connector\u003c\/li\u003e\n\u003cli\u003eAir Pressure Regulator\/Water Trap (separate air dryer is required to reduce consumable wear and prevent torch damage)\u003c\/li\u003e\n\u003cli\u003eConsumable Starter Kit\u003c\/li\u003e\n\u003cli\u003eWEiPU SP21 CNC Connector 12 Pin\u003c\/li\u003e\n\u003cli\u003e240\/120V Pigtail Adapter\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eOptional Equipment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eProtective Cover\u003c\/li\u003e\n\u003cli\u003eNOVA Welding and Fabrication Table\u003c\/li\u003e\n\u003cli\u003eNOVA Clamp and Tool Kit\u003c\/li\u003e\n\u003cli\u003eIPT-60 Hand Held Torch 24 ft.\u003c\/li\u003e\n\u003cli\u003eIPT-60 Plasma Consumables Kits\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eRecommended Areas of Use\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eMotorsports\u003c\/li\u003e\n\u003cli\u003eMuffler and sheet metal shops\u003c\/li\u003e\n\u003cli\u003eFarm\/Ranch\u003c\/li\u003e\n\u003cli\u003eHome Garages\u003c\/li\u003e\n\u003cli\u003eLight Fabrication Shops\u003c\/li\u003e\n\u003cli\u003ePortable Repair\u003c\/li\u003e\n\u003cli\u003eHVAC\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eRecommended Metals\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSteel\u003c\/li\u003e\n\u003cli\u003eStainless\u003c\/li\u003e\n\u003cli\u003eAluminum\u003c\/li\u003e\n\u003cli\u003eCopper\u003c\/li\u003e\n\u003cli\u003eTitanium\u003c\/li\u003e\n\u003cli\u003eNickel\/Nickel Alloys\u003c\/li\u003e\n\u003cli\u003eMost any metal\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eType\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eIGBT\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eVoltage\/phase\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eDual Voltage 120\/240 1 Phase\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOutput Amp\/Volt Range\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e120V: 20-30A\/ 88-92V\u003cbr\u003e240V: 20-60A\/ 88-104V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOCV\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e300V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMax Inrush ( I1MAX ) Amps\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e120V: 36A\u003cbr\u003e240V: 41A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMaximum Rated (I1EFF ) Input Amps\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e120V: 22A\u003cbr\u003e240V: 25A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eDuty Cycle At Rated Amps\/Volts\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e120V: 35% @ 30A rated @ 40° C\u003cbr\u003e240V: 35% @ 60A rated @ 40° C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eArc Start Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eBlow Back (Piston type)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePilotArc\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eTorch Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eiPT 60 (Innotec)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eCNC Interface Port\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eNo\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eAdjustable Post Flow Timer\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eNo\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eGouging\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eNot Recommended\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRecommended Cutting Air Pressure\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e65-72 PSI\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRecommended Compressor Capacity\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e5.3 CFH @ 90 PSI\/ 20-30 Gallon reserve\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOK-to-Cut Indicator\/Low Air pressure safety\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eAmps\/Volts @ 60% Duty Cycle\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e120V: 25A\u003cbr\u003e240V: 50A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eAmps\/Volts @ 100% Duty Cycle\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e120V: 20A\u003cbr\u003e240V: 40A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eWarranty\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e5 year\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eShipping Weight\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e35 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePart Number\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eEV-HTC60\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e","brand":"Everlast","offers":[{"title":"Default Title","offer_id":50925443186850,"sku":"EV-HTC60","price":649.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0616\/9985\/0402\/files\/8c693c0cd0715a477a9197ab5616dff5.png?v=1795135313"}],"url":"https:\/\/www.weldshopsupply.com\/collections\/everlast-plasma-cutters.oembed","provider":"Weld Shop Supply","version":"1.0","type":"link"}